Alert: Notifications at reduced capacity during COVID-19 restrictions
We are operating at reduced capacity due to the COVID 19 alert level four requirements.
Please only call our 0800 number if someone is at serious risk of harm or has been seriously injured, become seriously ill, or died as a result of work.
For other notifications please complete our online forms at Notify WorkSafe.
The purpose of these guidelines is to help reduce the risk of injuries from manual handling on farms by providing practical guidance on how to manage hazards.
While this guidance has not been updated to reflect current work health and safety legislation (the Health and Safety at Work Act 2015 and regulations), it may still contain relevant information and practices to keep workers and others healthy and safe.
Please read this guidance in conjunction with all relevant industry standards that apply to you as a PCBU. This guidance will be progressively reviewed and either updated, replaced with other guidance, or revoked.
- Workers must be trained in correct techniques for manual handling jobs
- No one should lift something that is too heavy for them
- Lift with the legs, not the back
- (Re)design the workplace to minimise manual handling hazards
- Use mechanical/lifting aids where possible
- Plan regular breaks and rotate jobs
01 / Introduction
This guideline is about preventing injuries from manual handling on farms.
Farm workers do a wide variety of manual handling tasks. The tasks involve using force, repetitive movements, stooping, static and awkward postures, continual bending and twisting at the waist, and handling heavy objects.
These can cause several problems, including:
- serious back injuries
- musculoskeletal disorders, including occupational overuse syndromes
- acute injuries, like muscle or tendon sprains and strains
- injuries from slips, trips and falls.
Manual handling is also one of many inter-related risks for acute low back pain.
This guideline identifies the dangers and risks from manual handling in farming and offers recommendations to help avoid accidents and injuries. WorkSafe accepts these recommendations as current industry best practice. They will help you comply with the Health and Safety in Employment Act 1992 (the HSE Act).
This guide is for farmers, employers, employees, principals, contractors; health and safety advisers; health and safety representatives, consultants and designers. The guide encourages employers and employees to work together to prevent harm when carrying out manual handling tasks on the farm.
Use this guide:
- to review how existing manual handling tasks are carried out on the farm
- when designing and carrying out new jobs involving manual handling
- when designing or changing equipment or work processes
- when manufacturing, importing or supplying equipment.
Industry experts helped WorkSafe develop this guide. WorkSafe also reviewed accident statistics, published academic literature and how overseas health and safety regulators manage the same issues.
WorkSafe has made every effort to ensure the guide’s recommended hazard controls reflect current best practice.
02 / About manual handling
Manual handling involves lifting, lowering, pushing, pulling, carrying, throwing, moving, restraining, holding or handling any animate, or inanimate object.
2.1 Hazardous manual handling tasks
A hazardous manual handling task involves one or more of the following:
|Lifting and stacking hay bales|
|Carrying feed or water buckets|
|Lifting concrete posts|
|Handling frightened or resistant animals|
|Attaching milking cups|
|Bending over to attach milking cups in a shallow pit|
|Bending and twisting during shearing or crutching|
|Driving a tractor or quad bike over rough ground|
|Using a chainsaw or shearing handpiece|
These aspects of manual handling put stress on the body and can cause injuries.
2.2 Musculoskeletal disorders (msds)
Manual handling can harm your musculoskeletal system (your bones and muscles) slowly, so the injury gets worse over time (a chronic injury). Manual handling accidents can also cause immediately-felt (acute) injuries, like cuts or broken bones.
Injuries and pain in the lower back are the most common work-related MSDs.
- muscle, ligament and tendon sprains and strains
- back injuries, including muscle, tendon, ligament, spinal disc, nerves, joint and bone damage
- joint and bone injuries or weakening, including shoulder, elbow, wrist, hip, knee, ankle, hand and foot injuries
- nerve injuries or compression, like carpal tunnel syndrome
- muscular and blood vessel conditions from hand-arm vibration (eg white knuckle)
- soft tissue hernias
- ongoing, long-term (chronic) pain.
MSDs are caused in two ways:
- Repeated or continual use of the same body part gradually wears down joints, ligaments, muscles and discs in the spinal cord. These movements include static body positions, like carrying buckets of water.
- Sudden damage is caused by strenuous work or unexpected movements (such as handling animals that move or change position suddenly).
- A combination of these also can also cause harm, for example, you could be more likely to get injured from manual handling if your body is weakened by damage that’s built up over time.
03 / How to identify and control manual handling hazards
There are several ways to identify manual handling hazards on the farm.
3.1 Review records
Farm records are a good source of information for identifying hazardous manual handling tasks. Look at hazard registers, accident investigation forms and early reports of discomfort. Use these records to find the locations and tasks where people were harmed from manual handling tasks.
- where in the workplace the problem occurred
- the person’s job
- what they were doing at the time
- the body part harmed (for example, the lower back or ankle)
- what the problem was (for example, a strain, open wound or broken bone)
- what went wrong.
When reviewing these records, think about:
- how many accidents or injuries are caused by particular manual handling tasks
- how often do injuries happen
- the total workload of each worker – that is, the time spent doing all the different manual handling tasks.
3.2 Talk with employees
Employees can help you understand potentially unsafe tasks. Employees know about the manual handling tasks they do, and how and when they do them. Employees can identify the exact tasks or actions they find tiring or hard to do. They can also help identify suitable controls to reduce the harm.
3.3 Watch people doing manual handling tasks
Watch all manual handling tasks to identify the hazards. Not all manual handling is harmful, so it is important to focus on the work that could cause harm.
Involve employees, contractors and principals to find out what they do. Watch them in detail and ask them to help you carry out the evaluation.
You can do this by:
- watching the worker do the task
- using checklists to make sure proper procedures are followed
- taking part in the task (where it is safe to do so).
If you have found one or more manual handling hazards in a task, or if written records or talks with employees show there is the potential for harm, you should assess the manual handling hazards.
3.4 Assessing manual handling hazards
If you find unsafe manual handling tasks, you (and your employees, contractors and principals) should assess the risk level each task poses. As employers, farmers must control the hazard and tell workers how to keep themselves safe.
To assess manual handling hazards, you must:
Assess the contributing factors:
When you’ve identified the contributing factors, you can control the task hazards.
See the ‘Loads’ section of this Guideline for more information on how different types of loads can harm people.
Decide how significant the contributing factors are
For each contributing factor you find, decide how risky it is, based on the information you’ve gathered.
Once you’ve assessed the contributing factors and decided how significant they are, you have the information you need to manage the hazard.
3.5 Limiting manual handling injuries
Think about how people manage their work. Make sure your employees know which manual handling tasks are hazardous and how to reduce the risk of injury.
- Remind employees that tasks should be smooth and controlled, never rushed.
- Teach them how to handle animals – avoid using brute force, which increases the risk of injury.
- Encourage them to share loads, to use lifting equipment, to handle only as necessary and not beyond their ability.
- Provide opportunities for employees to change their posture regularly, and to move and stretch between tasks.
- Encourage employees to keep fit.
- Encourage early reporting of signs of back pain. Most back problems are short term and not serious. The best way to deal with acute back pain is to stay active and keep moving – building up strength gradually and avoiding heavy duties.
- If back pain is ongoing or severe, get medical advice to make sure there are no serious problems, like fractures or bone infections.
3.6.1 Heavy loads
Handling heavy objects needs a lot of strength. This means tissues and joints in the back, knees, arms and shoulders are overloaded.
A lighter weight held away from the body needs the same effort to handle as a heavy one held close.
Jerking or moving a load quickly uses more force than just carrying the load.
WorkSafe NZ cannot set out specific weight limits (because manual handling is a complex process involving a lot of different risks), but the more weight or force needed, the more likely it is someone will be hurt.
3.6.2 Bulky or awkward loads
A bulky load:
- needs an awkward and twisted posture
- makes it hard to keep the weight close to the body
- increases the load on spine and joints.
3.6.3 Unpredictable or difficult to move loads
Unpredictable loads, like lodged or stuck items, need more force to move. This is also the case with awkward postures or sudden, uncontrolled movements.
3.6.4 Loads with uneven weight distribution
These put demands on the person handling the load and might overload some muscle groups. The shape might stop the heavy end being held close to the body.
3.6.5 Unstable or unbalanced loads
Loads like fluids and sacks of shifting contents need extra muscle effort to control them. The person might have to use sudden, uncontrolled movements if the contents suddenly tip.
3.6.6 Loads that block the person’s view
Loads can cause twisted postures if the handler tries to get a better view. Injuries can also happen from slipping or falling.
3.6.7 Loads that are difficult to grip, greasy or slippery
If gripping the load is difficult, the handler might have to use their hand and arm muscles in a constant high force. Sudden, uncontrolled movements happen if they lose their grip. Gloves might make it easier to get a better grip, but they might increase the force needed to grip the load securely.
3.6.8 Loads with handles
Handles reduce the force needed to move a load and increase precision and ease of movement. The location, shape, position and size of handles are all important.
3.6.9 Very hot or cold loads or those that contain hazardous substances
The load’s temperature or its chemical make-up influence how the load is handled. The handler might need protective clothing or equipment. The load might have to be held away from the body.
3.6.10 Animal handling
Animals pose unique handling problems, like how to grip the animal and how to counter unpredictable movements. How much help the animal can give, whether it cooperates, and how much pain it might experience also affect the way each animal should be handled.
3.6.11 Loads with sharp edges
Loads with sharp edges are unsafe and add to manual handling hazards.
04 / Types of hazardous manual handling tasks
The different types of manual handling hazards faced on farms are outlined in this section, along with management strategies.
4.1 Lifting and moving objects on the farm
Lifting and moving objects can involve high, sustained, repetitive or sudden forces. Some examples are:
- lifting and stacking hay bales
- carrying feed or water buckets
- lifting concrete posts
- handling frightened or resistant animals.
These contribute to lower-back pain, injury and other MSDs.
Uneven, steep or slippery terrain makes the risks of lifting and moving objects worse.
Remember that most back injuries don’t happen suddenly. Back injuries often happen over many years of wear and tear, making the discs between the vertebrae weak and more likely to rupture.
Managing the hazard:
Do not try to lift objects that are too big or heavy for you. Find ways to avoid lifting heavy items. If you must lift them, use your legs, not your back and keep the load in front of and close to your body. During long shifts, change tasks around to give your muscles a break.
Buy products in bulk or on a pallet that can be loaded using a forklift, front-end loader or augers.
- Make sure the bulk load is secure with straps, chains or other fixtures.
- Install automatic feeders.
- Buy smaller or ready-to-use amounts of products you don’t use often.
- Use powered equipment or mechanical aids (eg front-end loaders) instead of lifting by hand.
- Use wheeled trolleys, dollys, wheelbarrows, ramps and other mechanical aids.
- Balance the load by carrying quantities in each hand; for instance, two buckets, one in each hand.
- Get help with lifting bags and heavy objects if you’re carrying them over steep or slippery ground.
- Keep a safe lifting posture by keeping your back straight, the load close to your body and lifting by bending your legs.
- Make object surfaces easier to grip by attaching handles or using gloves.
- Break down awkward or heavy loads into smaller packages, drums, bags or packets.
- Make sure liquid loads are in containers that make handling easier, such as lightweight plastic with easy-to-use handles.
- Keep your equipment in good condition and replace worn parts – if you reduce friction, you reduce the force needed to move things.
4.2 Sustained postures
Any posture you hold for a time is a sustained posture, like bending for too long or using only one group of muscles. Examples are drenching cattle, hoof paring or driving a tractor. Holding one position can tire out the muscles you are using. It can lead to muscle strains, aches, pains or other MSDs.
Sustained postures are made more hazardous by:
- using high force
- long duration
- high mental demand combined with unsafe manual tasks, such as inspection work.
Managing the hazard:
Plan regular rest breaks so you don’t hold awkward positions for too long.
Regular rest breaks give workers the chance to avoid or recover from tired muscles caused by unsafe manual handling tasks.
Rotate jobs often.
Rotate staff between different tasks to increase variety, this reduces the risk of MSDs. The tasks need to be different enough to make sure different muscle groups are used, giving the body a chance to recover.
Alter the working position.
Workers should not stay in seated, standing or other fixed postures for a long time.
For workers doing seated or standing tasks, get them to change their postures and movements. Examples are:
For seated tasks (unless the backrest interferes with the actions) use seats with:
- an adjustable seat height
- adjustable backrest angle
- a backrest that fits the spine
- a swivel action so workers don’t have twist to reach.
For standing tasks use:
- a chair, stool or support so the worker can alternate between sitting and standing
- a footrest (large enough for the whole foot) so you can stand with either foot raised
- where possible, suitable floor covering to cushion concrete and other hard floors.
A standing work position is best when:
- handling large, heavy or bulky loads
- using forceful movements
- moving in and out of the work area often
- lacking knee room or space.
4.3 Repetitive actions
Repetitive actions – like attaching and detaching milking cups, drenching or using pruning tools – can tire out the affected muscles. Over time, aches and pains or other MSDs appear.
Managing the hazard:
Avoid double handling, share heavy workloads and use mechanical aids where possible.
Avoid excessive handling or double handling by planning work and storing objects in suitable areas.
- Share heavy workloads between workmates, rotate tasks, or spread physical handling tasks over a work week.
- Use turntables, hoists, trolleys and slides to move objects, instead of relying on body strength.
4.4 Overreaching or handling with the arms outstretched
Some farming tasks involve overreaching or handling with the arms outstretched. Examples include working in the milking pit with the milking clusters or drenching and de-horning cattle.
Managing the hazard:
Use mechanical aids where possible.
Mechanical equipment reduces or eliminates the need for workers to lift, carry or support items, animals or people. A wide range of equipment is available for different farm activities. Use turntables, hoists, trolleys and slides to move objects, rather than relying on body strength.
4.5 Whole body vibration
Some farm tasks involve prolonged exposure to whole body vibration, such as working all day on a tractor or quad bike. Prolonged and repeated exposure to whole body vibration can lead to MSDs.
Managing the hazard:
Take steps to dampen vibration and plan regular rest breaks.
Using vibration-damped equipment and engine mountings are a good way to reduce exposure to vibration. Other choices include:
- improving vehicle suspension
- installing operator seats on suspension systems with spring and damper elements
- keeping vibration-reducing measures well maintained
- making sure workers adjust their seats to fit
- using equipment within the manufacturers’ recommendations or to a speed that reduces vibration
- telling workers about the risks of whole- body vibration and how to keep safe
- taking regular breaks.
Tell farm staff about hand-arm vibration. Use different work methods if they can eliminate the need for vibrating equipment. If this is not possible, buy tools and equipment that produce less vibration.
Being tired can make manual handling hazards worse. Problems like poor time management, planning and deadlines can lead to problems, like trying to do too much because of deadline pressures. Sometimes there isn’t enough communication or planning. This means work is often done in less than ideal conditions and can result in worker fatigue.
Working while physically fatigued increases the chances of MSDs developing. Working while mentally fatigued increases the chance of accidents happening. '
Managing the hazard:
Plan work in advance so people don’t have to work unreasonable hours.
4.7 Poor workplace design
Poorly designed workplaces can increase the chances of accidents or injuries.
Managing the hazard:
Get professional design advice when planning improvements or conversion. Keep the things you use most often in easy to reach places. Reduce carrying distances. Plan and design for easy handling; for example, storing heavy objects at waist height, avoiding the need to open doors while carrying loads and reducing how much you need to move objects around.
Think about the workplace’s design and layout. Redesign or adapt by:
- Moving equipment and loads closer to where they are handled.
- Raising work surfaces to waist height to reduce bending, twisting, outstretched handling and awkward postures.
- Reduce or remove manual handling tasks where surfaces are slippery. Use lifting equipment, cover outdoor areas and wear footwear with a good grip.
- Keep yards in good condition. Remove trip and slip hazards. Make sure gates open easily.
- Improve drainage in work areas, such as around yards and sheds.
- Temperatures affect physical and mental capacity. Wear warm clothes when it’s cold and light clothes when it’s warm.
- Workers may need to wear personal protective equipment (PPE); that is, safety gear. This can make manual handling more difficult and hazardous.
- Beware of high winds – strong or gusty winds can catch a load and can blow you off balance.
- Be careful in dull or very bright conditions. Sharp and sudden contrasts between lighting (like moving from indoors to outdoors) or glare increase the chances of slips, trips and falls. Make sure farm buildings are correctly lit.
- Poor air quality affects work ability.
HEALTH & SAFETY IN EMPLOYMENT REGULATION 16
Raised objects: If you are working under something that has been lifted off the ground, then put supports or similar devices under it to stop it falling.
05 / Specific hazards and controls
The most common manual handling hazards on farms are outlined in this section. Recommendations on how to manage these hazards are provided.
Milking cluster handling is one of the most frequent and repetitive manual handling tasks on a dairy farm. Repetitive manual handling, particularly in awkward positions (like attaching milking clusters in a shallow pit), can cause harm.
Specific tasks that can cause injury:
- handling milking clusters
- putting on and taking off clusters while bent in an awkward posture
- releasing clusters from automatic cup removers (ACRs).
An obvious hazard is a mismatch between worker height and pit depth or rotary height.
Managing the hazard:
Set up your workplace to reduce the need to bend, twist or load.
Reduce injuries by keeping the work in front, between shoulder and mid-thigh height. This helps people to work in a position that keeps the natural lumbar curve in the lower back.
Some ways to achieve this:
- Make sure the farm dairy is designed to let workers milk comfortably – a position that reduces their need to overreach or bend continuously.
- Consider designing or changing a cups-on/ off area so it adjusts to suit the worker’s height. Keep everything within reach or within the shoulder-hip area.
- Put idle clusters on brackets and jetters at a height that reduces bending and reaching.
- Retrofit vacuum release valves on ACR rams.
- Use ACRs wherever practicable.> Use rubber ‘fatigue’ matting in the pit to reduce the strain of standing for a long time.
- Provide clear access to the udders by planning the height of kick rails or splash guards.
- Review workers’ cups-on technique to reduce repetitive overreaching.
- Change jobs to reduce repetitious manual handling tasks, including rotating between cups-on and cups-off positions.
- Use teat spray wands with a long nozzle to reduce the need to bend. This also reduces the chance of being kicked and exposed to spray.
5.2 Herd testing
Herd testing can also put people at risk of developing getting MSDs.
Managing the hazard
Removing herd test sample flasks:
- Design the workplace so workers can take samples from a comfortable posture.
Sorting sample flasks on a bench:
- Design a herd sample sorting table that reduces reaching and bending.
Moving trays of samples through the shed to a vehicle:
- Use a trolley to transport samples to the vehicle.
- Package samples at the collection point.
- Limit the number of samples per tray to a comfortable carrying weight.
- Keep the walkway clear of obstacles at floor and head height.
- Remove trip or slip hazards.
- Reduce the need to repeatedly transfer samples into trays.
- Give the person taking the herd samples a milking shed safety induction.
- Make sure the herd tester has modern equipment like mini-flasks. These flasks accept a smaller sample and weigh less.
- Install a trough at working height in the shed.
5.3 Lifting sheep
Sometimes sheep have to be lifted, for example, over a fence. Sheep are large, heavy animals and can fight against being lifted. This can cause back strains and twisting injuries.
Managing the hazard:
Avoid lifting sheep if possible. Use gates and ramps where available. If a sheep must be lifted, use your legs, not your back.
Some sheep weigh almost 100 kg. Only people with enough strength should lift sheep. Don’t make someone lift a sheep if they cannot physically do it.
The correct technique for lifting a sheep is:
- Hold the sheep against the rail and straddle its rump. Put one hand on the rail, the other under the sheep’s neck.
- Using the rail for support, take the strain off your back and pull the sheep onto its hind legs.
- Move your hand, from the rail, under the sheep’s nearest leg and grasp the opposite front leg.
- Move your other hand from the neck and firmly grasp the fold of skin between the belly and hind leg.
- Crouch behind the sheep, bend your knees, take the weight on your knees and hold the sheep firmly.
- Stand up using your legs, not your back, and lift the sheep off the ground.
- Swing the sheep towards the top of the fence, boosting it with your leg.
- Put the sheep on top of the rail and let it see the ground.
- With a slight rolling movement, let the sheep fall onto its feet.
5.4 Lifting calves
Often it is necessary to lift a new-born calf; this causes many back injuries.
Managing the hazard:
Lift using your legs and keep your back as straight as possible.
To lift, squat down beside the calf, pull it in close with one arm around the front and the other around the hind legs. Straighten your knees to lift it. Hold it firmly and don’t let it struggle loose.
Calves quickly grow and become very heavy. No one should lift a calf if it is too heavy for them.
5.5 Shearing and crutching
Shearing and crutching are high-risk jobs that need a lot of manual effort. Back strains are likely because the work is repetitive and done in an awkward, bent-over position.
Contractors who shear or crutch thousands of sheep each year can be at high risk of injury. However, the less practised farmer – who is likely to have a poorer technique and less suitable gear – is also at risk of injury.
Managing the hazard:
Use the correct techniques when shearing and crutching. Thoroughly train people who do this work.
Tips for lifting objects
- Balance your body’s weight equally over both feet.
- Step close to the load.
- Think about the best place to grip the load and the best type of grip to use.
- Apply force gradually, after testing the weight.
- Lift smoothly, rather than using sudden exertion.
- Hold the load close to your body.
- To change direction while moving, take a step in the new direction rather than twisting your body.
- Pace the work if it goes on for a long time, take small breaks often.
Sheep can be crutched standing (with their head in a bail or crutching plant, or held with your knees against a rail) or sitting up across the shearing board.
Use the correct techniques to catch and drag sheep across the board:
- Hold the sheep against your braced knees with one hand under the chin and one on the rump.
- Turn the sheep’s head to the rear while forcing the rump down against your leg with your other hand.
- When the sheep is no longer standing on its feet, lift the front leg and sit the sheep securely on its rump.
To save effort and avoid back strain when pulling the sheep across the shearing board, get the animal to walk backwards and then sit it on its rump.
Take special care of your back when shearing or crutching. Using a good technique avoids unnecessary pressure on your back and keeps your spine straight while under load.
- Keep your lower back warm, particularly in draughty woolsheds. Use a back-warmer and wear more layers during breaks.
- Take every chance to straighten and extend your back beyond straight when standing or lying down.
- Use a lumber support while sitting at break times.
- A back support (bungy) supports the upper body and is recommended for back problems. When using a back support ensure it is attached securely and doesn’t touch electrical wiring.
Crutching sheep standing in the race lessens back strain and increases output, although it is usually only suitable when doing light dagging or crutching.
To learn more about shearing safety, see WorkSafe NZ’s Best Practice Guideline for Shearing.
5.6 Shearing handpieces
A worn out, poorly adjusted or maintained handpiece will vibrate, heat up, cut poorly and put more physical strain on the crutcher or shearer’s hands and arms. It can also cause a mechanical lock-up, which can break bones and seriously wound the user and people nearby.
Managing the hazard:
Handpieces must be kept in good working order.
Keep the handpiece in the best possible condition and replace worn parts. Where crutchers and shearers are required to supply and maintain their own handpiece, they are also responsible for keeping it in good order.
Regular safety checks should include:
- Correct comb and cutter set-up on the handpiece: check screws are tight, fork pins are secure in the cutter holes and tension is on.
- The tension pin should work, stopping the tension from releasing.
- The spline drive, connecting the handpiece to the downtube, should release easily.
- The leather guard protecting the cogs must be effective.
Use worm (spline) drives. They reduce the risk of serious injury from lock-up.
06 / Training requirements
Employers must give employees information and training about each hazardous manual handling task that hasn’t been eliminated from the farm.
6.1 General requirements
Employees must have the knowledge and experience to work safely. If they don’t, they must be supervised by someone with that knowledge and experience so they don’t harm themselves or others. Train employees how to use plant, objects, substances, equipment, and relevant PPE safely.
Record when training occurred and who was trained.
Competent employees should know:
- how to do the task properly and safely
- what the hazards of the job are
- how to control the hazards
- how to use equipment and lifting aids properly and safely
- effects of contributing factors on manual handling: load, environment, people, task and management
- how to carry out a basic task assessment to identify hazardous manual handling tasks
- safe handling principles (such as being close to the load)
- when and how to use PPE.
Training cannot fix problems like:
- poor work area layout
- lack of mechanical aids or using inappropriate ones
- unsuitable loads
- poor working conditions.
6.2 Training for health and safety representatives
The Health and Safety in Employment Act 1992 gives employees the right to be involved in workplace health and safety matters. One way to do this is by electing a health and safety representative. This is someone who employees can go to when they have any concerns or suggestions regarding health and safety in the workplace. The representative will work with the employer in good faith to find a solution.
This representative can take two days paid leave each year to undergo approved health and safety training.
07 / References
|Acute Injuries||An injury caused by a recent traumatic event (usually within a day or so of the event). Injuries include bruises, cuts, broken bones.|
|All Practicable Steps||
Section 2A Health and Safety in Employment Act 1992:
The steps taken to achieve the result that it is reasonably practicable to take in the circumstances, having regard to:
‘To avoid doubt, a person required by the Health and Safety in Employment Act 1992 to take all practicable steps is required to take those steps only in respect of circumstances that the person knows or ought reasonably to know about.’
|Asymmetrical Posture||A posture that requires the body to twist or bend to one side or to bear the weight unevenly on the feet.|
|Auger||A mechanism that uses a rotating screw blade, called a ‘flighting’, usually within a tube, to move liquid or other materials, like animal feed.|
AS 2865 Confined Spaces:
‘An enclosed or partially enclosed space that is not intended or designed primarily for human occupancy, within which there is a risk of one or more of the following:
|Contributing Factors (Manual Handling)||The things that make manual handling hazards more serious and more frequent, such as load, environment, people, task and management.|
|Control or Control Measure||A way of eliminating, isolating or minimising the risk of harm in any task.|
Section 2(1) of the Health and Safety in Employment Act 1992:
“An activity, arrangement, circumstance, event, occurrence, phenomenon, process, situation or substance…that is an actual or potential cause or source of harm”.
|Hazardous Manual Handling||
Any manual handling task with one or more of the following:
|Load||The object being handled or the forces being applied.|
|Manual Handling||Any activity requiring a person to interact with their environment and use any part of their muscles or skeletal system to lift, lower, push, pull, carry, throw, move, restrain or hold any object, whether animate or not.|
|Manual Handling Task||Specific manual handling action or activity. It may be one part of a job.|
|Musculoskeletal Disorders (Work-Related)||A collective name for a range of conditions that affect the muscles, tendons, bones and joints. This term includes occupational overuse syndromes, back injuries and acute low back pain.|
|Occupational Overuse Syndrome (OOS)||An umbrella term for a range of disorders characterised by pain and/or other sensations in muscles, tendons, nerves, soft tissues and joints with evidence of clinical signs. Overuse syndromes are musculoskeletal disorders.|
|Personal Protective Equipment (PPE)||Items of personal equipment worn for protection of some sort; ear muffs, gloves and boots are examples.|
|Plant||Any appliance, equipment, fitting, furniture, implement, machine, machinery, tool or vehicle (and any part of, controls for or anything connected to that plant).|
“Not exposed to any hazards or free from hazards.”
Section 2(1) Health and Safety in Employment Act 1992
“Any of the following conditions that amounts to or results in permanent loss of bodily function, or temporary severe loss of bodily function:
First Schedule to the Health and Safety in Employment Act 1992
Section 2(1) of the Health and Safety in Employment Act 1992:
‘Significant hazard means a hazard that is an actual or potential cause or source of—
|Strains and Sprains||These terms are used in the sense of their normal meanings in a medical diagnosis.|
|Workplace Design||The design of the workplace – in relation to the characteristics of the people who will use the workplace and the work that will be done in it.|
Farming Activities and Carrying and Lifting: The Agricultural Health Study E. Francine, et al. Journal of Physical Activities and Health, 9(1) 2012
Interventions to Reduce Low-Back Injury Risk Among Youth Who Perform Feed Handling and Scooping Tasks on Farms W. G. Allread & T. R. Waters. Journal of Agricultural Safety and Health, 13(4) 2007, pp. 375–393
Investigation of Select Ergonomic Interventions for Farm Youth. Part 1: Shovels S. E. Kotowski, K. G. Davis, & T. R. Waters. Journal of Agromedicine, 14(1) 2009
Investigation of Select Ergonomic Interventions for Farm Youth. Part 2: Wheelbarrows S. E. Kotowski, K. G. Davis, & T. R. Waters. Journal of Agromedicine, 14(1) 2009
Low Back Pain Among Irish Farmers D. O’Sullivan, C. Cunningham, & C. Blake. Occupational Medicine, 59(1) 2009
Physical Demands and Low-Back Injury Risk Among Children and Adolescents Working on Farms J. R. Wilkins, W. G. Allread, W. S. Marras, & T. R. Waters. Journal of Agromedicine 10(4) 2003
Prevention of Musculoskeletal Disorders for Children and Adolescents Working in Agriculture (Conference Proceedings) National Institute of Occupational Safety and Health, DHHS (NIOSH) Publication Number 2004-119, 2004
Secondary Injury Caused by Lifting S. D. Jepsen, K. McGuire, & Danielle Poland. Ohio AgrAbility Fact Sheet Series – AEX-981.1-10, Ohio State University Extension
Work-Related Injuries and Fatalities on Dairy Farm Operations: A Global Perspective D. I. Douphrate, et al. Journal of Agromedicine, 18(3) 2013, pp. 256–264
Work-Related Musculoskeletal Disorders Among Irish Farm Operators A. Osborne et al. American Journal of Industrial Medicine, 56, 2013, p. 235–242
New Zealand guidance
Code of Practice for Manual Handling OSH and ACC, 2001
Farm Workers: Preventing and Managing Discomfort, Pain & Injury ACC, 2011
Preventing Manual Handling Injuries for the Farmer ACC, 2002
Guidance from other countries
Agricultural Workbook (AU) Department of Commerce, Western Australia (Section 8 Manual handling)
E-Facts 14: Hazards and Risks Associated with Manual Handling in the Workplace European Agency for Safety and Health at Work
Farmwise: Your Essential Guide to Health and Safety in Agriculture (UK) Health and Safety Executive, 2013 (HSG270 Section 21 Manual handling)
Good Agricultural Practices and Good Handling Practices (US) Oregon Department of Agriculture
Hazardous Manual Tasks: Code of Practice (AU) Safe Work Australia, 2011
Manual Handling at Work (UK) Health and Safety Executive, 2012
Manual Handling (UK) Health and Safety Executive